Search

Durethan T40 000000

  _More Info 
  _Data sheet ISO (PDF) 

 

Data sheet

PA 6I, non-reinforced, injection molding, extrusion
 
ISO/ ASTM
 
ISO Shortname:  ISO 16396-PA 6I,,GT,S12-030
PropertyTest ConditionUnitStandardguide value
 d.a.m.cond.
Rheological properties
Molding shrinkage, parallel150x105x3; 270 °C / WZ 80 °C; 500 bar%acc. ISO 25770.53
Molding shrinkage, transverse150x105x3; 270 °C / WZ 80 °C; 500 bar%acc. ISO 25770.49
Post- shrinkage, parallel150x105x3; 100 °C; 4 h%acc. ISO 25770.13
Post- shrinkage, transverse150x105x3; 100 °C; 4 h%acc. ISO 25770.09

Mechanical properties (23 °C/50 % r. h.)
CTensile modulus1 mm/minMPaISO 527-1,-233003000
CYield stress50 mm/minMPaISO 527-1,-211090
CYield strain50 mm/min%ISO 527-1,-26.05.0
CCharpy impact strength23 °CkJ/m²ISO 179-1eUNN
CCharpy impact strength-30 °CkJ/m²ISO 179-1eUNN
CCharpy notched impact strength23 °CkJ/m²ISO 179-1eA< 10< 10
CCharpy notched impact strength-30 °CkJ/m²ISO 179-1eA< 10< 10
Charpy notched impact strength-40 °CkJ/m²ISO 179-1eA< 10< 10
Izod notched impact strength-30 °CkJ/m²ISO 180-1A< 10< 10
Izod notched impact strength-40 °CkJ/m²ISO 180-1A< 10< 10
Flexural modulus2 mm/minMPaISO 178-A30003000
Flexural strength2 mm/minMPaISO 178-A150130
Flexural strain at flexural strength2 mm/min%ISO 178-A7.05.0
Flexural stress at 3.5 % strain2 mm/minMPaISO 178-A105110

Thermal properties
CTemperature of deflection under load1.80 MPa°CISO 75-1,-2105
CTemperature of deflection under load0.45 MPa°CISO 75-1,-2115
Vicat softening temperature50 N; 120 °C/h°CISO 306125
CCoefficient of linear thermal expansion, parallel23 to 55 °C10-4/KISO 11359-1,-20.7
CCoefficient of linear thermal expansion, transverse23 to 55 °C10-4/KISO 11359-1,-20.8
CBurning behavior UL 941.5 mmClassUL 94V-2
CBurning behavior UL 940.75 mmClassUL 94V-2
Glow wire test (GWFI)2.0 mm°CIEC 60695-2-12960
CVicat softening temperature50 N; 50 °C/h°CISO 306125

Electrical properties (23 °C/50 % r. h.)
CRelative permittivity100 Hz-IEC 602504.34.6
CRelative permittivity1 MHz-IEC 602503.84.0
CDissipation factor100 Hz10-4IEC 60250400480
CDissipation factor1 MHz10-4IEC 602509001100
CVolume resistivityOhm·mIEC 600931E131E13
CSurface resistivityOhmIEC 600931E151E15
CElectric strength1 mmkV/mmIEC 60243-12528
CComparative tracking index CTISolution ARatingIEC 60112600

Other properties (23 °C)
CWater absorption (Saturation value)Water at 23 °C%ISO 626.0
CWater absorption (Equilibrium value)23 °C; 50 % RH%ISO 622.0
CDensitykg/m³ISO 11831180

Processing conditions for test specimens
CInjection molding-Melt temperature°CISO 294270
CInjection molding-Mold temperature°CISO 29480

Processing recommendations
Drying temperature dry air dryer°C -80
Drying time dry air dryerh -2-6
Residual moisture content%Acc. to Karl Fischer 0.03-0.12
Melt temperature (Tmin - Tmax)°C -260-280
Mold temperature°C -80-100
CThese property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.
Disclaimer
Standard Disclaimer
The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products, technical assistance and information to determine to your own satisfaction whether they are suitable for your intended uses and applications. This application-specific analysis must at least include testing to determine suitability from a technical as well as health, safety and environmental standpoint. Such testing has not necessarily been done by us. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale. All information and technical assistance is given without warranty or guarantee, and is subject to change without notice. It is expressly understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in connection with the use of our products, technical assistance and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with patents covering any material or its use. No license is implied or in fact granted under the claims of any patent.
Typical Properties
Property data is provided as general information only. Property values are approximate and are not part of the product specifications.
Flammability
Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions.
Health and Safety
Appropriate literature has been assembled which provides information concerning the health and safety precautions that must be observed when handling LANXESS products mentioned in this publication. Before working with these products, you must read and become familiar with the available information on their hazards, proper use, and handling. This cannot be overemphasized. Information is available in several forms, e.g., material safety data sheets (MSDS) and product labels. Consult your LANXESS Corporation representative or contact the Product Safety and Regulatory Affairs Department at LANXESS. For materials that are not LANXESS products, appropriate industrial hygiene and other safety precautions recommended by their manufacturer(s) must be followed.
Regulatory Compliance
Some of the end uses of the products described in this brochure must comply with applicable regulations, such as the FDA, NSF, USDA and CPSC. If you have any questions on the regulatory status of any LANXESS engineering thermoplastic, consult your LANXESS Corporation representative or contact the LANXESS Regulatory Affairs Manager.
Medical
Medical BIOCOMPATIBILITY INFORMATION: All LANXESS resins (hereinafter "Product(s)") designated as "medical grade" have met the requirements of the FDA-Modified ISO 10993, Part I "Biological Evaluation of Medical Devices" tests with human tissue contact time of 30 days or less. ONLY THESE PRODUCTS MAY BE CONSIDERED CANDIDATES FOR APPLICATIONS REQUIRING BIOCOMPATIBILITY. No "medical grade" Product will be made available for sale until successful completion of the above testing by LANXESS. Regrind resins must not be used in medical applications requiring biocompatibility. MANUFACTURER'S RESPONSIBILITY: It is the responsibility of the medical device, biological product or pharmaceutical manufacturer ("Manufacturer") to determine the suitability of all component parts and raw materials, including any LANXESS Product, used in its final product in order to ensure safety and compliance with FDA requirements. This determination must include, as applicable, testing for suitability as an implant device and suitability as to contact with and/or storage of human tissue and liquids including, without limitation, medication, blood or other bodily fluids. Under no circumstances may any LANXESS Product be used in any implant applications (cosmetic, reconstructive or reproductive). Nor may any LANXESS Product be used in any other bodily implant applications, or any applications involving contact with or storage of human tissue, blood, or other bodily fluids, for greater than 30 days, based on the FDA-Modified ISO 10993 tests. The suitability of a LANXESS Product in a given end-use environment is dependent upon various conditions including, without limitation, chemical compatibility, temperature, part design, sterilization method, residual stresses or external loads. It is the responsibility of the Manufacturer to evaluate its final product under actual end-use requirements and to adequately advise and warn purchasers and users thereof. Single-use medical devices made from a LANXESS Product are not suitable for multiple uses. If the medical device is designed for multiple uses, it is the responsibility of the Manufacturer to determine the appropriate number of permissible uses by evaluating the device under actual sterilization and end-use conditions and to adequately advise and warn purchasers and users thereof. STERILIZATION INFORMATION: The sterilization method and the number of sterilization cycles a medical device made from a LANXESS Product can withstand will vary depending upon type/grade of product, part design, processing parameters, sterilization temperature and chemical environment. Therefore, the Manufacturer must evaluate each device to determine the sterilization method and the number of permissible sterilization cycles appropriate for actual end-use requirements and must adequately advise and warn purchasers and users thereof.
Color and Visual Effects
Type and quantity of pigments or additives used to obtain certain colors and special visual effects can affect mechanical properties.
LANXESS Corporation | Pittsburgh, PA 15275
Date: 01.05.2019