Rheological properties |
C | Melt volume-flow rate | 250 °C; 2.16 kg | cm³/(10 min) | ISO 1133-1 | 8 |
| Molding shrinkage, parallel | 150x105x3; 260 °C / MT 80 °C; 600 bar | % | acc. ISO 294-4 | 1.6 |
| Molding shrinkage, transverse | 150x105x3; 260 °C / MT 80 °C; 600 bar | % | acc. ISO 294-4 | 1.6 |
| Post- shrinkage, parallel | 150x105x3; 150 °C; 1 h | % | acc. ISO 294-4 | 0.5 |
| Post- shrinkage, transverse | 150x105x3; 150 °C; 1 h | % | acc. ISO 294-4 | 0.5 |
Mechanical properties (23 °C/50 % r. h.) |
C | Tensile modulus | 1 mm/min | MPa | ISO 527-1,-2 | 2600 |
C | Yield stress | 50 mm/min | MPa | ISO 527-1,-2 | 55 |
C | Yield strain | 50 mm/min | % | ISO 527-1,-2 | 4.0 |
C | Nominal strain at break | 50 mm/min | % | ISO 527-1,-2 | >50 |
C | Charpy impact strength | 23 °C | kJ/m² | ISO 179-1eU | N |
C | Charpy impact strength | -30 °C | kJ/m² | ISO 179-1eU | 230 |
C | Charpy notched impact strength | 23 °C | kJ/m² | ISO 179-1eA | <10 |
C | Charpy notched impact strength | -30 °C | kJ/m² | ISO 179-1eA | <10 |
| Izod impact strength | 23 °C | kJ/m² | ISO 180-1U | N |
| Izod impact strength | -30 °C | kJ/m² | ISO 180-1U | 180 |
| Izod notched impact strength | 23 °C | kJ/m² | ISO 180-1A | <10 |
| Izod notched impact strength | -30 °C | kJ/m² | ISO 180-1A | <10 |
| Flexural strength | 2 mm/min | MPa | ISO 178-A | 85 |
| Flexural strain at flexural strength | 2 mm/min | % | ISO 178-A | 6.0 |
| Flexural stress at 3.5 % strain | 2 mm/min | MPa | ISO 178-A | 75 |
C | Puncture energy | 23 °C | J | ISO 6603-2 | 23 |
C | Puncture energy | -30 °C | J | ISO 6603-2 | 16 |
C | Puncture maximum force | 23 °C | N | ISO 6603-2 | 3877 |
C | Puncture maximum force | -30 °C | N | ISO 6603-2 | 3926 |
Thermal properties |
C | Melting temperature | 10 °C/min | °C | ISO 11357-1,-3 | 225 |
C | Temperature of deflection under load | 1.80 MPa | °C | ISO 75-1,-2 | 60 |
C | Temperature of deflection under load | 0.45 MPa | °C | ISO 75-1,-2 | 140 |
C | Temperature of deflection under load | 8.00 MPa | °C | ISO 75-1,-2 | 45 |
| Vicat softening temperature | 50 N; 120 °C/h | °C | ISO 306 | 170 |
C | Coefficient of linear thermal expansion, parallel | 23 to 55 °C | 10-4/K | ISO 11359-1,-2 | 1.3 |
C | Coefficient of linear thermal expansion, transverse | 23 to 55 °C | 10-4/K | ISO 11359-1,-2 | 1.3 |
C | Burning behavior UL 94 | 1.5 mm | Class | UL 94 | HB |
C | Burning behavior UL 94 | 0.75 mm | Class | UL 94 | HB |
Electrical properties (23 °C/50 % r. h.) |
C | Relative permittivity | 100 Hz | - | IEC 60250 | 3.4 |
C | Relative permittivity | 1 MHz | - | IEC 60250 | 3.2 |
C | Dissipation factor | 100 Hz | 10-4 | IEC 60250 | 15 |
C | Dissipation factor | 1 MHz | 10-4 | IEC 60250 | 200 |
C | Volume resistivity | | Ohm·m | IEC 62631-3 | >1E13 |
C | Surface resistivity | | Ohm | IEC 62631-3 | >1E15 |
C | Electric strength | 1 mm | kV/mm | IEC 60243-1 | 30 |
C | Comparative tracking index CTI | Solution A | Rating | IEC 60112 | 600 |
Other properties (23 °C) |
C | Water absorption (Saturation value) | Water at 23 °C | % | ISO 62 | 0.5 |
C | Water absorption (Equilibrium value) | 23 °C; 50 % RH | % | ISO 62 | 0.2 |
C | Density | | kg/m³ | ISO 1183 | 1300 |
| Bulk density | | kg/m³ | ISO 60 | 800 |
Material specific properties |
C | Viscosity number | | cm³/g | ISO 1628-5 | 158 |
Processing conditions for test specimens |
C | Injection molding-Melt temperature | | °C | ISO 294 | 260 |
C | Injection molding-Mold temperature | | °C | ISO 294 | 80 |
Processing recommendations |
| Drying temperature circulating air dryer | | °C | - | 120 |
| Drying time circulating air dryer | | h | - | 4-8 |
| Residual moisture content | | % | Acc. to Karl Fischer | 0.00-0.02 |