Durethan BLUEB30SF 000000

  _Mehr Infos 
  _Datenblatt ASTM (PDF) 



PA 6, non-reinforced, injection molding, suitable for food-contact
ISO Shortname:  ISO 16396-PA 6,(R),GR,S14-030
PropertyTest ConditionUnitStandardguide value1
 dry as moldedconditioned

Mechanical properties (23 °C/50 % r. h.)
Tensile modulus1 mm/minlb/in²ASTM D 638464000159000
Tensile stress at yield-lb/in²ASTM D 638116005800
Tensile elongation at yield-%ASTM D 6384.020
Tensile elongation at break-%ASTM D 63835> 50
Tensile stress at break-lb/in²ASTM D 63872508700
Izod notched impact strength73 °F, 0.125 inft·lb/inASTM D 2561.114
Flexural modulus-lb/in²ASTM D 790392000102000
Flexural stress at 5 % strainlb/in²ASTM D 790167005080

Thermal properties
Deflection temperature under load, Unannealed66 psi; 0.157 in°FASTM D 648356
Deflection temperature under load, Unannealed264 psi; 0.157 in°FASTM D 648140
UL94 Flame ClassThickness tested: 1.5 mmClassUL 94V-2
UL94 Flame ClassThickness tested: 3.0 mmClassUL 94V-2
Relative temperature index, mechanical with impactThickness tested: 1.5 mm°CUL 746B65
Relative temperature index, mechanical without impactThickness tested: 1.5 mm°CUL 746B75
Relative temperature index, electricalThickness tested: 1.5 mm°CUL 746B105

Electrical properties (23 °C/50 % r. h.)
Dissipation factor50 Hz-IEC 602500.052.3
Dissipation factor1 MHz-IEC 602500.070.4
Volume resistivityOhm·mIEC 600931E131E10
Surface resistivityOhmIEC 600931E131E12
Dielectric strength0.118 inV/milIEC 60243-1762889
Dielectric constant, Tinfoil electrodes50 Hz-IEC 602503.820
Dielectric constant, Tinfoil electrodes1 MHz-IEC 602503.44.6
Comparative tracking index CTIVASTM D 3638600

Other properties (23 °C)
Densitylb/in³ASTM D 7920.041
Specific gravity-ASTM D 7921.14

1Typical properties: these are not to be construed as specifications
Disclaimer for commercial products
This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice does not release you from the obligation to verify the information currently provided - especially that contained in our safety data and technical information sheets - and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery.
Test values
Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Kindly note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mould/die, the processing conditions and the coloring.
Processing note
Under the recommended processing conditions small quantities of decomposition product may be given off during processing. To preclude any risk to the health and well-being of the machine operatives, tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at the workplace in accordance with the Safety Data Sheet. In order to prevent the partial decomposition of the polymer and the generation of volatile decomposition products, the prescribed processing temperatures should not be substantially exceeded. Since excessively high temperatures are generally the result of operator error or defects in the heating system, special care and controls are essential in these areas.
Conditioning in accordance with ISO 1110 (70 °C; 62 % r.h.)
Envalior Deutschland GmbH | DE 40474 DUESSELDORF | Deutschland
Datum: 22.12.2023