Search

Pocan B7616 000000
  _More Info 
  _Data sheet ISO (PDF) 

 

Data sheet
PBT+PC, 15% glass fibers, injection molding, low tendency to warp, improved surface finish
 
ISO Shortname:  ISO 20028-PBT+PC,GF15,GHMR,09-050
PropertyTest ConditionUnitStandardguide value1
Rheological properties
CMelt volume-flow rate260 °C; 2.16 kgcm³/(10 min)ISO 1133-117
CMolding shrinkage, parallel60x60x2; 250 °C / WZ 80° C; 600 bar%ISO 294-40.7
CMolding shrinkage, transverse60x60x2; 250 °C / WZ 80° C; 600 bar%ISO 294-40.5
Post- shrinkage, parallel60x60x2; 120 °C; 4 h%ISO 294-40.4
Post- shrinkage, transverse60x60x2; 120 °C; 4 h%ISO 294-40.2

Mechanical properties (23 °C/50 % r. h.)
CTensile modulus1 mm/minMPaISO 527-1,-24600
CTensile Stress at break5 mm/minMPaISO 527-1,-275
CTensile Strain at break5 mm/min%ISO 527-1,-24.2
CCharpy impact strength23 °CkJ/m²ISO 179-1eU45
CCharpy impact strength-30 °CkJ/m²ISO 179-1eU50
CCharpy notched impact strength23 °CkJ/m²ISO 179-1eA< 10
CCharpy notched impact strength-30 °CkJ/m²ISO 179-1eA< 10
Izod impact strength23 °CkJ/m²ISO 180-1U35
Izod impact strength-30 °CkJ/m²ISO 180-1U40
Izod notched impact strength23 °CkJ/m²ISO 180-1A< 10
Izod notched impact strength-30 °CkJ/m²ISO 180-1A< 10
Flexural modulus2 mm/minMPaISO 178-A4500
Flexural strength2 mm/minMPaISO 178-A130
Flexural strain at flexural strength2 mm/min%ISO 178-A4.7
Flexural stress at 3.5 % strain2 mm/minMPaISO 178-A120
Ball indentation hardnessN/mm²ISO 2039-1160

Thermal properties
CMelting temperature10 °C/min°CISO 11357-1,-3225
CTemperature of deflection under load1.80 MPa°CISO 75-1,-2105
CTemperature of deflection under load0.45 MPa°CISO 75-1,-2135
CTemperature of deflection under load8.00 MPa°CISO 75-1,-275
Vicat softening temperature50 N; 120 °C/h°CISO 306145
CCoefficient of linear thermal expansion, parallel23 to 55 °C10-4/KISO 11359-1,-20.5
CCoefficient of linear thermal expansion, transverse23 to 55 °C10-4/KISO 11359-1,-20.8
CBurning behavior UL 941.5 mmClassUL 94HB
CBurning behavior UL 940.75 mmClassUL 94HB
Resistance to heat (ball pressure test)°CIEC 60695-10-2150
Glow wire test (GWFI)2.0 mm°CIEC 60695-2-12750

Electrical properties (23 °C/50 % r. h.)
CRelative permittivity100 Hz-IEC 602503.5
CRelative permittivity1 MHz-IEC 602503.4
CDissipation factor1 MHz10-4IEC 60250130
CVolume resistivityOhm·mIEC 62631-3> 1E13
CSurface resistivityOhmIEC 62631-3> 1E15
CElectric strength1 mmkV/mmIEC 60243-134
CComparative tracking index CTISolution ARatingIEC 60112200

Other properties (23 °C)
CWater absorption (Saturation value)Water at 23 °C%ISO 620.4
CWater absorption (Equilibrium value)23 °C; 50 % RH%ISO 620.1
CDensitykg/m³ISO 11831350
Bulk densitykg/m³ISO 60800

Processing conditions for test specimens
CInjection molding-Melt temperature°CISO 294250
CInjection molding-Mold temperature°CISO 29480

Processing recommendations
Drying temperature circulating air dryer°C -120
Drying time circulating air dryerh -4-8
Residual moisture content%Acc. to Karl Fischer 0.00-0.02
Melt temperature (Tmin - Tmax)°C -250-260
Mold temperature°C -80-100

Notes
1Typical properties: these are not to be construed as specifications
CThese property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.
Disclaimer
Standard Disclaimer
The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products, technical assistance and information to determine to your own satisfaction whether they are suitable for your intended uses and applications. This application-specific analysis must at least include testing to determine suitability from a technical as well as health, safety and environmental standpoint. Such testing has not necessarily been done by us. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale. All information and technical assistance is given without warranty or guarantee, and is subject to change without notice. It is expressly understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in connection with the use of our products, technical assistance and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with patents covering any material or its use. No license is implied or in fact granted under the claims of any patent.
Typical Properties
Property data is provided as general information only. Property values are approximate and are not part of the product specifications.
Flammability
Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions.
Health and Safety
Appropriate literature has been assembled which provides information concerning the health and safety precautions that must be observed when handling Envalior products mentioned in this publication. Before working with these products, you must read and become familiar with the available information on their hazards, proper use, and handling. This cannot be overemphasized. Information is available in several forms, e.g., material safety data sheets (MSDS) and product labels. Consult your Envalior representative or contact the Product Safety and Regulatory Affairs Department. For materials that are not Envalior products, appropriate industrial hygiene and other safety precautions recommended by their manufacturer(s) must be followed.
Regulatory Compliance
Some of the end uses of the products described in this brochure must comply with applicable regulations, such as the FDA, NSF, USDA and CPSC. If you have any questions on the regulatory status of any Envalior engineering thermoplastic, consult your Envalior representative or contact the Regulatory Affairs Manager.
Color and Visual Effects
Type and quantity of pigments or additives used to obtain certain colors and special visual effects can affect mechanical properties.
Envalior Performance Materials LLC | Pittsburgh, PA 15275
Date: 20.12.2023